Hello everyone.
I just purchased a Sprint Note 4 (SM-n910P) that has Android 5.1.1 currently installed. While I know there is no current chainfire autoroot for this version of android, I was planning on downloading to 5.0.1 using the ROM file from SamMobile that I downloaded. So I enabled developer mode, enabled USB debugging, and used Odin to flash and downgrade to 5.0.1. I used vol down, Power, and Home to go into the Odin Mode on the phone, plugged it into a Windows 10 PC using Odin 3.10.6. Odin recognizes the com port and I load up the correct .tar.md5 file. I press start and immediately receive a FAIL inside of Odin. This is on the Odin screen:
<OSM> N910PVPU3BOF5_N910PSPT3BOF5_N910PVPU3BOF5_HOME.tar .md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> aboot.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007> sbl1.mbn
<ID:0/007> rpm.mbn
<ID:0/007> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
While on the phone I receive the following:
SW REV CHECK FAIL : [about]Fused 4 > Binary 3
[1] eMMC write fail: ABOUT
Can anyone tell me what I am doing wrong? I am experienced at rooting and flashing roms on my HTC Evo 4G and my Note 2 which I've had for a combined 5+ years. I've tried Odin 3.07, 3.10, older Samsung USB Cable, newer USB cable. I have Kies installed with the latest USB drivers installed.
Is this an issue with my computer or with the phone itself? After it fails numerous times I'm able to reboot the phone back into the normal settings and continue using it as if nothing happened. CAN I downgrade this to 4.4.4 through 5.0.1 if I choose too? Or does 5.1.1 somehow magically prevent all of that from happening? Advice? Comments? Suggestions??
Thanks!
I just purchased a Sprint Note 4 (SM-n910P) that has Android 5.1.1 currently installed. While I know there is no current chainfire autoroot for this version of android, I was planning on downloading to 5.0.1 using the ROM file from SamMobile that I downloaded. So I enabled developer mode, enabled USB debugging, and used Odin to flash and downgrade to 5.0.1. I used vol down, Power, and Home to go into the Odin Mode on the phone, plugged it into a Windows 10 PC using Odin 3.10.6. Odin recognizes the com port and I load up the correct .tar.md5 file. I press start and immediately receive a FAIL inside of Odin. This is on the Odin screen:
<OSM> N910PVPU3BOF5_N910PSPT3BOF5_N910PVPU3BOF5_HOME.tar .md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> aboot.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007> sbl1.mbn
<ID:0/007> rpm.mbn
<ID:0/007> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
While on the phone I receive the following:
SW REV CHECK FAIL : [about]Fused 4 > Binary 3
[1] eMMC write fail: ABOUT
Can anyone tell me what I am doing wrong? I am experienced at rooting and flashing roms on my HTC Evo 4G and my Note 2 which I've had for a combined 5+ years. I've tried Odin 3.07, 3.10, older Samsung USB Cable, newer USB cable. I have Kies installed with the latest USB drivers installed.
Is this an issue with my computer or with the phone itself? After it fails numerous times I'm able to reboot the phone back into the normal settings and continue using it as if nothing happened. CAN I downgrade this to 4.4.4 through 5.0.1 if I choose too? Or does 5.1.1 somehow magically prevent all of that from happening? Advice? Comments? Suggestions??
Thanks!
Aucun commentaire:
Enregistrer un commentaire